Aeroelasticity & Structural Dynamics in a Fast Changing World
17 – 21 June 2024, The Hague, The Netherlands
Home Program Author Index Search

Design, manufacturing and identification of an active controlled flexible wing for subsonic wind tunnel testing


Go-down ifasd2024 Tracking Number 121

Presentation:
Session: Wind tunnel testing 1
Room: Room 1.1
Session start: 13:30 Tue 18 Jun 2024

Johannes Dillinger   Johannes.Dillinger@dlr.de
Affifliation: DLR - Institute of Aeroelasticity, Bunsenstrasse 10, 37073 Goettingen, Germany

Holger Mai   Holger.Mai@dlr.de
Affifliation: DLR - Institute of Aeroelasticity, Bunsenstrasse 10, 37073 Goettingen, Germany

Wolf R. Krüger   Wolf.Krueger@dlr.de
Affifliation: DLR - Institute of Aeroelasticity, Bunsenstrasse 10, 37073 Goettingen, Germany

Thomas Schmidt   TG.Schmidt@dlr.de
Affifliation: DLR - Institute of Aeroelasticity, Bunsenstrasse 10, 37073 Goettingen, Germany

Felix Stalla   felix.stalla@dlr.de
Affifliation: DLR - Institute of System Dynamics and Control, Muenchener Strasse 20, 82234 Wessling, Germany


Topics: - Computational Aeroelasticity (High and low fidelity (un)coupled analysis methods:), - Aeroservoelasticity (Vehicle analysis/design using model-based and data driven models), - Active Control and Adaptive Structures (Vehicle analysis/design using model-based and data driven models), - Experimental Methods in Structural Dynamics and Aeroelasticity (Experimental methods), - Wind Tunnel and Flight Testing (Experimental methods)

Abstract:

To minimize the climate impact of commercial flight, aircraft emissions have to be significantly reduced. Important contributions towards this goal are the reduction both of aircraft drag and of structural mass. An increase of wing aspect ratio is a well-known design measure to reduce induced drag, however, a higher wing span usually leads to higher wing mass because of increased structural loads. Thus, load alleviation is essential for the realization of high aspect ratio wings, active gust load alleviation being a promising step to further decrease sizing loads. The paper presents the design, manufacturing and testing of an actively controlled wing in the German Aerospace Center (DLR) project oLAF (optimized load adaptive wing). A wing of 1.75m semi-span is designed and built, equipped with five trailing edge devices (flaperons/ailerons) and two spoilers. The sensors built into in the wing include 12 accelerometers, 10 pressure sensors and a fiber-optical sensor for strain measurements. Furthermore, the forces and moments of a piezo-balance in the wind tunnel mounting are available for feedback, and a marker-based optical measurement system is used for the high-speed tracking of wing and control surface deflections. The wind tunnel campaign takes place at the DNW-NWB subsonic wind tunnel in Braunschweig, a tunnel belonging to the German and Dutch Wind Tunnel organization. The wind tunnel has a cross section of 3.25m x 2.8m and is operating at a maximum flow speed of 90m/s. For the experiment, a gust generator is specifically designed, based on four stationary airfoil vanes, each followed by a downstream rotating, slotted cylinder (RSC) mounted vertically. Load control is implemented on a real-time environment based on control laws being developed in MATLAB/Simulink. The design of the wing, as well as that of the gust generator, is supported by comprehensive numerical studies. The wind tunnel model structure is designed, manufactured and equipped using our in-house aeroelastic model design process. The transfer functions of the actuators, required for the control design, are identified in a specific set-up on the model. The dynamic properties of the model structure are identified both wind-off in a standard ground vibration test (GVT), and wind-on at specific test points for identification. The paper focuses on the design and construction of the wing. Separate papers will give a specific view on design and analysis of the gust generator, as well as on the design of the control laws, and an overview of the test matrix, the data acquisition systems and control hardware, and finally of the experimental results.